By Steve McManus | November 24, 2018 11:57:25I recently had a friend send me a MSR Guardian purifier for my son.
I love this purifier!
I’ve never had a problem with them, so it was a no brainer for me to buy them.
My son has allergies, but not as much as he does.
When he is allergic, his nose becomes very dry.
The MSR purifiers are not water based, and when they dry, they can become very irritating to his nasal passages.
So I went ahead and ordered two.
They arrived on my doorstep in two weeks, and the first one was out in the rain, so I went to take it for a spin.
Once inside, it’s very easy to remove.
You’ll notice it’s a very thick plastic, so you’ll need a pair of tongs to remove it.
This is what you need to do to get it out of the water.
After that, you’re free to go ahead and put it in the dryer for a few minutes.
Now, you’ll notice the MSR is quite water resistant, and it comes with a couple of things to help with keeping it cool: a little bit of extra water, and a bit of a magnet.
To make sure it’s working, you can put the magnet on the bottom of the purifier so you don’t lose it, and then take a deep breath and rub it in.
A little bit goes a long way.
At this point, I had already ordered the other two, so now I just need to get the purifiers out of my house and onto my truck.
For now, I’m just going to keep them in the car.
As soon as they’re in the back of the truck, I’ll get them out of there.
But, there’s a lot more to do.
Next, I need to make sure they’re clean and dry.
First off, you should put the purifying unit in a zip lock bag and keep it away from the air.
Then, you need a small dishwasher and a bowl of warm water.
Here’s how you do that.
Put the bowl in the washing machine.
In this example, it has the washing cycle turned off.
Then, start the washing.
Don’t be afraid to let the machine run for a minute or two, just to ensure that the water is flowing and that the bowl is getting a good rinse.
It may seem like a lot of water, but remember that the purification unit is just a plastic container.
Let the water run for about 10 seconds.
Take the bowl out of its bag and let it sit for about 5 seconds.
Now, start using the bowl again.
Again, you don�t have to let it run for much longer than 5 seconds to get that clean, watery surface.
With the bowl back in the bag, start draining the water out of it.
You’ll have to be careful not to hit anything, because the water will collect on the surface of the bowl and be stuck there for a long time.
Wipe down the bowl a little, and add a little more water.
Now that the dishwasher is finished, it�s time to put the lid on.
If you have a large bowl, you may want to put a towel on top to protect it from the heat of the washing machines.
Here’s the process:Put the lid in the dishwashing machine.
Take out the bowl.
Make sure the bowl isn�t stuck in the bottom, or else you may start a fire.
Put the towel in there.
Remove the bowl from the dishwash machine.
Get a towel.
Place the bowl inside the washing bag, and put the bowl on the top.
Get a bucket.
Use a little pressure to push the bowl into the bowl, and start to rinse.
When the water runs out of this bag, put the bucket back in.
Let it drain for a while.
Repeat for the other bowl.
Now, start on the next bowl.
I put the bowls in the wash machine in order, but I always start the next one first.
(The washing cycle is turned off, so the washing bags are placed on the counter so they drain more quickly.)
The last thing you need for this is a little piece of tape.
Just stick the tape in the bowl the same way you did with the bowl before, and repeat.
That should be it for the first bowl, but you could add more water, or do whatever you want with the bowls, if you like.
Be sure to keep a close eye on the bowls.
They can get really messy, especially if you